Standard Playground Sets

W szkołach, w których liczba uczniów w klasach I-III przekracza 69 osób, Program Radosna Szkoła zakłada utworzenie tzw. „dużego” placu zabaw o pow. ok. 500 m2.

Maksymalna kwota dofinansowania (50% wartości inwestycji) wynosi 115.450 zł. Warto zaznaczyć, że jest to 50% maksymalnej kwoty jaką macie Państwo do dyspozycji.

Wizualizacja 3D - Duży Plac Zabaw - Program Radosna Szkoła

Budowa placów zabaw, ogólne założenia są następujące:

• plac ma być wyposażony w urządzenia z trwałych i bezpiecznych materiałów. Urządzenia mają posiadać 36 miesięczną gwarancję oraz mają być zgodne z wymaganiami normy PN-EN 1176 co musi być potwierdzone odpowiednim atestem.
• wybór sprzętu ma się odbywać głównie pod kątem zapewnienia dzieciom możliwości rekreacji ruchowej. Preferowane są urządzenia o funkcjach gimnastycznych, takie jak np. wszelkie przeplotnie, drabinki, zestawy zabawowe, huśtawki itp.. Choć nie jest to wprost napisane, Ministerstwo niechętnie patrzy na umieszczane w projektach piaskownice i karuzele.

Nawierzchnie bezpieczne dla szkół:

• zakłada się utworzenie 3 stref funkcjonalnych, z których każda wyposażona jest w odpowiednia nawierzchnię:
• Strefa zabaw i ćwiczeń – pow. około 240 m2, o nawierzchni bezpiecznej piankowej (np. nawierzchnia bezpieczna SAMBA) lub gumowej w kolorze pomarańczowym, zbliżonym do RAL 2011,
• Strefa komunikacyjna – pow. około 50 m2, o nawierzchni syntetycznej (np. nawierzchnia bezpieczna SAMBA) w kolorze niebieskim, zbliżonym do RAL 5003,
• Strefa zielona – pow. około 210 m2, trawiasta, do obsadzenia krzewami i drzewami.
• plac ma być wyposażony w ławki, kosze na śmieci oraz tablicę informacyjną zgodną z publikowanym na stronie MEN wzorem.
• dopuszcza się możliwość stosowania ogrodzeń placu zabaw, wysokości 1-1.5 m, wyposażonych w bramki wejściowe szerokości > 1 m z tym, że preferowane są wygrodzenia żywopłotowe.

Our surfacing doesn’t require a special prepared ground but can be easily installed at a 25-cm thick layer of compacted sand. There is no need to use an expensive foundation of aggregate or concrete. Such a solution reduce overall assembly costs.

Depending on the thickness of an impact absorbing pad, SAMBA Safety Surface can reach critical fall heights of 3 meters, which is certified for compliance with European standard EN 1177:2008

It is worth noting that falling on an artificial grass is less painful than falling on a harsh rubber granules.

THE MAIN ADVANTAGES OF SAMBA

• It doesn’t require an expensive foundation of aggregate or concrete except the edgings
• It may be installed directly on a levelled sandy surface
• It may be installed irrespective of weather conditions
• It allows an easy and inexpensive repairing of mechanical faults
• It enables changing playground arrangement if it’s necessary to relocate the facilities
• It allows reuse of some elements of the surface and reduce total costs
• It’s covered by manufacturer’s 24-mont warranty

AVAILABLE DIMENSIONS OF PLAYGROUND SAFETY SURFACING „SAMBA”

TECHNICAL DESCRIPTION

• Playground Safety Surfacing „SAMBA” is composed of shock absorbing pads made of recycled, waterproof polyurethane foam and a sand filled artificial turf.
• The thickness of the safety surface is determined for each device according to established Critical Fall Height (CFH)
• Instand disassembly and the possibility of reusing some elements of the surfacing
• It doesn’t require an expensive foundation of aggregate or concrete except the edgings
• Easy and inexpensive repairing of mechanical faults
• 24-month manufacturer’s warranty

The opportunity to choose between different thickness of shock absorbing pads and to combine them together allows for the accurate selection of the type of surfacing for particular playground device.

How to select the right playground safety surfacing?

Each of playground devices has strictly defined its Critical Fall Height parameter, measured in meters and complying with European standard PN-EN 1176. An impact absorbing surface shall be matched with Critical Fall Height value of equipment installed on a playground. If playground is equipped with different height devices, a safety surfacing shall be suited to the highest CFH value.

We offer you five SAMBA Safety Surfacing systems, according to different thickness of shock absorbing pads:

PRO-ECOLOGICAL SOLUTIONS

With regards to environment and landscape protection, we use constructional solutions that have minimal impact on the surroundings and comply with ecological requirements of reusing waste materials.

• Shock absorbing pads used in SAMBA Safety Playground Surfacing are made of recycled polyurethane foam
• To install our safety surface we use the minimum amount of synthetic adhesive
• Since the top layer of SAMBA system is made of artificial turf, our impact absorbing surface can blends in the surrounding landscape
• In case of closing down the playground, SAMBA surface can be instantly disassembled without leaving any pollution in the ground and part of the system can be reused.

ASSEMBLY INSTRUCTION

• STAGE 1 – Preparatory Work
  • Secure the assembly site to keep others at a distance.
  • Safety surface shall be installed in selected location while maintaining required impact area.
  • The thickness of the safety surface is determined for each device according to established Critical Fall Height (CFH).
• STAGE 2 – Installation of Playground Safety Surfacing „SAMBA”
  • Excavate a trench on the entire assembly site. The trench should measure 25 cm deep below safety surfacing level.
  • Place the two parallel concrete edgings on the sand & concrete foundation all along the inner edges of the trench. The distance between the two edgings should measure 15 mm. It is recommended to put a HDPE insert between the edgings every one meter. It’s important to note that the outer concrete edging should be placed at ground level while the inner concrete edging should be lowered and placed 10 mm below. Both edgings should be aligned with outward facing beveled edges (see diagram).
  • In order to preparing the foundation for the shock absorbing pads, fill the trench with sand or gravel. Take care that the sand does not enter to the gap between concrete edgings. Compact the sand and level the ground. The level of the sand surface should be lower than the outer concrete edgings by a thickness of o the shock absorbing pad.
  • Spread the shock absorbing pad all over the sand surface. If it’s necessary to trim the pad, use a sharp knife. 
  • If you use double layer system (one layer above the other), take care that the upper layer is moved in relation to the lower layer by a half of panel, so as panels connection points in particular layers do no coincide.
  • Cover the entire playground surface by tiles of artificial turf and at the same time cut out holes for bollards, trees, devices and the other objects.
  • In order to obtain unified playground surfacing, stick the tiles of artificial turf together from below using installation tape and two-component, polyurethane adhesive.
  • The layer of artificial turf should be 10 cm above the outer concrete edging all along the edge of playground. Put the resulting 10 cm overlap into the gap between two concrete edgings and then chock it by filling the gap with sand. Fill the entire surfacing with a dry, quartz sand (fraction 0,3 – 0,8 mm) - approximately 25 kg of sand per 1m2 of artificial turf.
  • Rub the sand manually between artificial turf fibers using an adequate brush to obtain an even surface.

Our products are painted with top quality, acrylic structural paints in the following colors:

Projektując plac zabaw warto spojrzeć na świat oczami dziecka.
Dziecko to mały odkrywca, każdy przedmiot z jakim się kontaktuje na co dzień wyzwala w nim ogromne pokłady kreatywności. Plac zabaw musi być miejscem w którym bezpieczna zabawa spotyka się z przygodą.